[Slackbuilds-users] rustup-1.26.0

[Barry J. Grundy]

On 23/08/13 07:48AM, John wrote:
> Yes Eric
> I discovered that, even though I had the shims installed my $PATH was not
> set properly. Barry's response got me thinking about that and enabled me to
> find my error and correct it. The $PATH had been properly set in the past.
> I must have changed it for some reason.
> Thank You
> John
 
Same here.  Shims installed, user path set up, but not the system. Much
appreciated.

Barry

> On Sat, Aug 12, 2023 at 10:55 PM Erich Ritz via SlackBuilds-users <
> slackbuilds-users at slackbuilds.org> wrote:
> 
> > ------- Original Message -------
> > On Saturday, August 12th, 2023 at 2:00 PM, Barry J. Grundy <
> > bgrundy at linuxleo.com> wrote:
> >
> >
> > >
> > >
> > > On 23/08/12 12:35PM, John wrote:
> > >
> > > > Greetings List
> > > > Rustup-1.26.0 fails to build for me with the following errors:
> > > >
> > > > --error: failed to get `anyhow` as a dependency of package `download
> > v1.26.0 (/tmp/SBo/rustup-1.26.0/download)`
> > > > Caused by:
> > > > failed to load source for dependency `anyhow`
> > > > Caused by:
> > > > Unable to update registry `crates-io`
> > > > Caused by:
> > > > failed to update replaced source registry `crates-io`
> > > > Caused by:
> > > > failed to parse manifest at
> > > > `/tmp/SBo/rustup-1.26.0/vendor/fs_at-0.1.3/Cargo.toml`
> > > > Caused by:
> > > > namespaced features with the `dep:` prefix are only allowed on the
> > nightly
> > > > channel and requires the `-Z namespaced-features` flag on the
> > command-line
> > > >
> > > > Any help is greatly appreciated for my System76 also needs
> > System76-power
> > > > which requires rustup
> > > > Thanks
> > > > john
> > >
> > >
> > > Interesting. Rustup installed fine for me, and after following the
> > > README instructions, I tried to install system76-power and recieved a
> > > very similar error to yours above:
> > >
> > > error: failed to get `clap` as a dependency of package `system76-power
> > v1.1.25 (/tmp/SBo/system76-power-fc8eb49fae5222da56dcfa414ef2b190e9f870c7)`
> > >
> > > Caused by:
> > > failed to load source for dependency `clap`
> > >
> > > Caused by:
> > > Unable to update registry `crates-io`
> > >
> > > Caused by:
> > > failed to update replaced source registry `crates-io`
> > >
> > > Caused by:
> > > failed to parse manifest at
> > `/tmp/SBo/system76-power-fc8eb49fae5222da56dcfa414ef2b190e9f870c7/vendor/anstream-0.3.2/Cargo.toml`
> > >
> > > Caused by:
> > > namespaced features with the `dep:` prefix are only allowed on the
> > nightly channel and requires the `-Z namespaced-features` flag on the
> > command-line
> > > make: *** [Makefile:62: target/release/system76-power] Error 101
> > > Failures:
> > > system76-power: system76-power.SlackBuild return non-zero
> > >
> >
> > I think you didn't configure your system to prefer rustup over system
> > rust.  See this user with the same error:
> >
> >
> > https://lists.slackbuilds.org/pipermail/slackbuilds-users/2023-January/027714.html
> >
> > >
> > > But again, rustup installed fine.
> > >
> > > Barry
> > > _______________________________________________
> > > SlackBuilds-users mailing list
> > > SlackBuilds-users at slackbuilds.org
> > > https://lists.slackbuilds.org/mailman/listinfo/slackbuilds-users
> > > Archives - https://lists.slackbuilds.org/pipermail/slackbuilds-users/
> > > FAQ - https://slackbuilds.org/faq/
> >
> > Erich
> > _______________________________________________
> > SlackBuilds-users mailing list
> > SlackBuilds-users at slackbuilds.org
> > https://lists.slackbuilds.org/mailman/listinfo/slackbuilds-users
> > Archives - https://lists.slackbuilds.org/pipermail/slackbuilds-users/
> > FAQ - https://slackbuilds.org/faq/
> >
> >
> 
> -- 
> Life expectancy in a firefight
> Radio Man 3 seconds
> Medic 7 seconds
> Officer whenever they get around to it.

> _______________________________________________
> SlackBuilds-users mailing list
> SlackBuilds-users at slackbuilds.org
> https://lists.slackbuilds.org/mailman/listinfo/slackbuilds-users
> Archives - https://lists.slackbuilds.org/pipermail/slackbuilds-users/
> FAQ - https://slackbuilds.org/faq/
>